L200pUser's Guide IBM ThinkVisionTM Monitor L200pEnglish
8Be sure to turn off the power before you perform any maintenance on themonitor. Clean your monitor as follows:• Do not use solvents or abrasives. • G
AENGLISH9Connecting your monitor1. Turn off your computer and all attached devices. Next, unplug all powercords to your computer and all attached devi
101. Switch on your computer.2. Switch on the monitor power source by pushing the power switch on siderear panel of the monitor. See Figure B on
ENGLISH11To install the device driver in Microsoft®Windows®95 or Windows 98, dothe following: Note:You must download files from the User’s Guide and I
12To install the device driver in Microsoft Windows 2000 Professional orMicrosoft Windows Millennium Edition (Me), do the following: Note:You must dow
ENGLISH13To install the device driver in Windows XP, do the following: Note:You must download files from the User’s Guide and Installation Files CD to
14For digital input, image setup is not required.When you first use your monitor, you must perform Auto Setup for analoginput. If you are using digita
ENGLISH15Image setup for DOSiIf the monitor is in standbymode, it may automaticallyturn off while you are waiting forit to warm up. If this happens,sw
6. When the dot pattern appears, press the " " button at the bottom ofthe monitor. This activates the Image setup procedure, which willo
Normally, you can complete the setup procedure using Automatic Image setup;however, if your screen image is still distorted after you perform Image se
iiiFirst Edition (April/2004)Note: For important information, refer to the Monitor Safety and Warranty manual that comes with this monitor.
18Adjusting your LCD monitorUser controlsUSER CONTROL FEATURESiThe image is alreadyoptimized for many displaymodes, however the usercontrols can be us
ENGLISH19The settings adjustable with the user controls are viewed through the On -Screen Display (OSD). Press the enter button " " to di
20OSD IconSelect the Color mode you find mostcomfortable or fine tune the colorsusing the Custom menu, if necessary.DescriptionSub-menu(s)• Clock• Pha
ENGLISH21Use this button to make the analog ordigital connector active. This featureis used when two computers areconnected to the monitor. The defaul
22iIf your computer haspreviously been used witha CRT monitor and is currentlyconfigured to a display modeoutside the range that the FlatPanel monito
ENGLISH23To benefit from power management, the monitor must be used inconjunction with a computer that implements the Video ElectronicsStandards Assoc
24TroubleshootingIf you have a problem setting up or using your monitor, you may be able to solve it yourself. Before calling your retailer or IBM, tr
ENGLISH25iFor image problems, youmay want to run Imagesetup again before referring tothis section. In most cases,Image setup can fix theproblems. See
26If you are unable to correct the problem yourself, you may seek further helpas follows:Call the IBM Service and Support.In the U.S.A and Puerto Rico
ENGLISH27iPower consumption figuresare for the monitor and thepower supply combined.SpecificationsThis color monitor (Type-model 6736-HC9) uses a 20.1
ENGLISH1Safety (Read first)...2Setting up the moni
28FRU MonitorFRU StandFRU Video CableFRU Video CableHybridHybridAnalogDigitalBBBBBlackBlack6736-HC96736-HC9 6736-HC9 6736-HC9 WWWWWWWWService informat
ENGLISH29Notices and trademarks This section contains information on notices and trademarks.NoticesIBM may not offer the products, services, or featur
30TrademarksThe following terms, used in this publication, are trademarks or service marks of theIBM Corporation in the United States, other countries
ENGLISH3Always observe the following precautions to reduce the risk of injury and property damage.Do not attempt to service a product yourself unless
4Be sure that the power outlet you are using is properly wired, easily accessible, and located close to theequipment. Do not fully extend power cords
ENGLISH5Setting up the monitorHandling instructions1. Lift the monitor by placing your hands where indicated by the arrows inthe figure below.2. Befor
6Kensington security slot3. Before adjusting your monitor for the first time, remove the locking clipon rear of the stand. Carefully hold the screen o
ENGLISH7iWith the IBM Flat PanelMonitor, you can adjustthe position in various waysfor maximum comfort.Viewing angleYou can tilt the screen forward an
Comments to this Manuals