IBM F50 User Manual Page 1

IBM RS/6000 7025 F50 Series IBMUser's Guide SA38-0540-01

Note: If any of the following Feature Codes are installed:3615, 4356, 4357, 4358, 4359, 6218, 8130, or 8134,or if a configuration using more than one

Set Power On Password: Setting a power-on password helps protect informationstored in your computer. You can use any combination of up to eight charac

Set Privileged-Access Password: The privileged-access password protects againstthe unauthorized starting of the system programs.If you previously had

Selecting the IP Parameters option displays the following screen.à ðIP Parameters 1. Client IP Address ... 2. Server IP Address ..

Selecting option 1 (3Com,3C905) displays the following 100Mb Ethernetconfiguration menus:à ð3Com Etherlink Fast XL1. Media Type [Auto]2. Full Duplex [

Selecting the Full Duplex option allows you to change how the Ethernet adaptercommunicates with the network:à ð .----------------.| Full Duplex || 1.

After choosing which adapter to use to ping the remote system, you must provide theaddresses needed to communicate with the remote system.à ðPing 1. C

Update System Firmware: This option allows you to update your systemfirmware. Note that you must insert a diskette containing the firmware update ima

Select LanguageThis option allows you to change the language used by the text-based SystemManagement Services screens.à ð SELECT LANGUAGE 1. Engl

3-40 IBM RS/6000 7025 F50 Series User's Guide

Chapter 4. Service Processor MenusThe Service Processor menus enable you to configure Service Processor optionsand to enamle and disable functions.Ser

Safety NoticesA danger notice indicates the presence of a hazard that has the potential of causingdeath or serious personal injury.A caution notice i

1 Operating system root password2 Privileged access password3 General access (power-on) passwordService Processor Functions ServiceProcessorMenus(ASCI

Service Processor MenusThe Service Processor menus are divided into two groups: General user menus - the user must know the general access password.

General User MenusThe menu options presented to the General user are a subset of the optionsavailable to the Privileged user. The user must know the G

 Read Progress Indicators from Last System BootDisplays the boot progress indicators (check points), up to a maximum of 100,from the system boot prio

Privileged User MenusThe following menus are available to privileged users only. The user must know thePrivileged Access Password in order to access t

Note: The information under the Service Processor Firmware heading in the MainMenu example that follows is example information only.à ðService Proces

Service Processor SETUP MENUà ðService Processor SETUP MENU1. Change Privileged Access Password2. Change General Access Password3. Enable/Disable Cons

PasswordsPasswords can be any combination of up to 8 alphanumeric characters. You canenter longer passwords, but the entries are truncated to include

When Console Mirroring is enabled, the Service Processor sends information toboth serial ports. This capability may be enabled by local or remote user

 Surveillance Setup MenuThis option may be used to setup operating system surveillance.à ðOS Surveillance Setup Menu 1. Surveillance: Currently Dis

DANGERTo prevent electrical shock hazard, disconnect the power cable fromthe electrical outlet before relocating the system.xii IBM RS/6000 7025 F50 S

SYSTEM POWER CONTROL MENUà ðSYSTEM POWER CONTROL MENU1. Enable/Disable Unattended Start Mode: Currently Disabled2. Ring Indicate Power-On Menu3. Rebo

– Ring Indicate Power-On may be set to 'Enabled' or 'Disabled'.– Number of Rings may be set to any number from 1 to 255. Reboot/R

historical comparison can be useful to System Administrators and servicepersonnel. Read Progress Indicators from Last System BootDisplays the boot pr

à ðSystem Environmental Conditions(System Power is currently off.)Fan : A stopped fan detectedFan 1: A stopped fan detectedFan 2: A stopped fan detec

CALL-IN/CALL-OUT SETUP MENUà ðCALL-IN/CALL-OUT SETUP MENU1. Modem Configuration Menu2. Serial Port Selection Menu3. Serial Port Speed Setup Menu4. Tel

For information on choosing a modem configuration file, see “Sample ModemConfiguration Files” on page D-1 and “Seamless Transfer of a Modem Session” o

You may enable and/or disable the call-in and call-out functions of each serial port inany combination.Serial Port Speed Setup Menuà ðSerial Port Spee

à ðTelephone Number Setup Menu1. Service Center Telephone Number: Currently Unassigned2. Customer Administration Center Telephone Number: Currently

For digital pagers that require a personal Identification Number (PIN) for access,include the PIN in this field as in the following example:1 8 123

If call out policy is set to 'all', the Service Processor will attempt a call out to allthe following numbers in the order listed: 1. Servi

Laser Safety InformationThe optical drive in this system unit is a laser product. The optical drive has a labelthat identifies its classification. The

Customer Account Setup Menuà ðCustomer Account Setup Menu1. Customer Account Number: Currently Unassigned2. Customer RETAIN Login UserID: Currently

Reboot/Restart Policy Setup MenuReboot describes bringing the system hardware back up from scratch, for example,from a system reset or power on. The b

2. The Use OS-Defined restart policy is set to YES and the operating systemhas NO automatic restart policy.Refer to “Service Processor Reboot/Restart

Local User Function User Interface Local async consoleText based menus with NLSOperator Panel messagesPower and Miscellaneous Power On/OffConfigurable

System Power-On Methods Power-on Switch - see “Starting the System Unit” on page 2-1. SP Menu power-on requestYou can request a power-on via the Ser

 Follow-up to a Failed Boot AttemptThe Service Processor will initiate a power-on sequence upon detection of afailed boot attempt.Service Processor R

Use OS-Defined restart policy?: The Use OS-Defined restart policy defaultsetting is YES. This causes the SP to refer to the OS Automatic Restart Poli

Service Processor System Monitoring - SurveillanceSurveillance is a function in which the Service Processor monitors the system, andthe system monitor

3. Surveillance delayThis is the length of time in minutes for the Service Processor to wait from whenthe operating system is started to when the fi

Call Out (Call-Home)The Service Processor can call out (Call-Home) when it detects one of the followingconditions: System firmware surveillance failu

Power Cables1234567891011Index Part Number Country1 1838574 Bahamas, Barbados, Bolivia, Brazil, Canada, Costa Rica,Dominican Republic, El Salvador, E

Console MirroringConsole mirroring allows a person on a local ASCII terminal to monitor the ServiceProcessor activities of a remote user. Console mir

Service Processor Firmware UpdatesThe Service Processor EPROM may need to be updated for two different reasons:1. The UPDATE (composite) portion of th

Refer to the downloaded update instructions, or to the System Management Services“Config” on page 3-5 or “Display Configuration” on page 3-26 or Servi

Updating Firmware from AIXYou must delete the file /var/update_flash_image before proceeding.The flash update image file must have already been placed

System POST Errors: If POST (Power-On Self Test) errors occur duringstart-up, this error log help isolate faults when used with the diagnostics.à ðRe

Chapter 5. Installing OptionsThis chapter provides instructions to help you add options to your system. Someoption-removal instructions are provided,

DANGERTo prevent electrical shock hazard, disconnect the power cable fromthe electrical outlet before relocating the system.5-2 IBM RS/6000 7025 F50 S

Handling Static-Sensitive DevicesAttention: Adapters, planars, diskette drives, and disk drives are sensitive to staticelectricity discharge. These de

Expansion BaysYour system comes with one 3.5-inch, 1.44MB diskette drive and a SCSI CD-ROMdrive. The number of preinstalled disk drives in your syste

Input/Output ConnectorsParallel Connector: One 25-pin parallel port is provided.Serial Connectors: Three 9-pin serial connectors (1, 2, and 3) are pr

Index Part Number Country8 14F0051 Liechtenstein, Switzerland9 14F0069 Chile, Ethiopia, Italy10 14F0087 Israel11 6952291 Paraguay, Colombia, Uruguay

Removing the Front Covers OnlyNote: If you are removing or installing hot-swap drives, only the front covers needto be removed. Other options may req

2. Remove the door by carefully lifting it up and off the hinges. Store it in a safeplace. Chapter 5. Installing Options 5-7

3. Remove the front cover:a. Unlock the keylock on the front cover.b. Lift up on the latch on the left side of the front cover.5-8 IBM RS/6000 7025 F5

c. Grasp the sides of the front cover at the top of the system and pull it forward.(The front cover is held in place by two spring detented ball studs

Removing Both the Front and Side CoversNote: If you previously removed the front covers, go to Step 3. 1. Open the door.5-10 IBM RS/6000 7025 F50 Ser

2. Remove the door by carefully lifting it up and off the hinges. Store it in a safeplace.3. Remove all media (diskettes, CDs, tapes) from the drives.

6. If you have a modem or fax machine attached to the system, disconnect thetelephone line.7. Unplug all power cords (cables) from electrical outlets.

8. Remove the front cover:a. Unlock the keylock on the front cover.b. Lift up on the latch on the left side of the front cover. Chapter 5. Install

c. Grasp the sides of the front cover near the top of the system and pull itforward. (The front cover is held in place by two spring detented ball stu

9. Remove the side cover:a. Pivot the side cover 90° away from the front of the system.b. Remove the cover by carefully lifting it up and off the hing

xvi IBM RS/6000 7025 F50 Series User's Guide

Removing the I/O Planar Cover1. If you have not already done so, remove the covers as described in “RemovingBoth the Front and Side Covers” on page 5-

Option List  Installing Memory Adapter Card. Go to page “Installing Memory” on page 5-18. Installing Memory–Module Kits — Go to page 5-24. Removin

Installing MemoryThe memory in your system is installed on memory cards, you can have up to twomemory cards installed. The memory DIMMs are installed

Note: Memory card 1 is the bottom card if there are two cards installed. If you onlyhave one memory card, it is memory card 1. For information on in

Installing or Adding Memory Adapter Cards1. If you have not already done so, remove the covers as described in “RemovingBoth the Front and Side Covers

10. Reinstall the memory shield on the bottom memory card..11. If you have other procedures to perform, refer to “Option List” on page 5-17.12. If you

Removing Memory Adapter Cards1. If you have not already done so, remove the covers as described in “RemovingBoth the Front and Side Covers” on page 5-

5. If you are installing a memory adapter card, see “Installing or Adding MemoryAdapter Cards” on page 5-20.6. If you have other procedures to perform

Memory-ModulesYou can increase the amount of memory in your system by installingmemory-modules on to an existing memory adapter card or if your syste

Adding or Replacing Memory to an Existing Card1. Remove the memory adapter card, see “Removing Memory Adapter Cards” onpage 5-222. Locate the memory

About This BookThis book provides information on how to install and remove options, use thesystem, use diagnostics, use service aids, and verify syste

b. Insert the memory module into the next unused memory module connector.Ensure that the tabs are in the unlocked position, as shown, prior to memorym

8. If you do not have any other procedures to perform, replace the I/O planar coveras described in “Replacing the I/O Planar Cover” on page 5-101; the

Removing Memory1. Remove the memory adapter card, see “Removing Memory Adapter Cards” onpage 5-22.2. Locate the memory module connectors and determi

StaticDevices5. Replace the memory card, see “Installing or Adding Memory Adapter Cards” onpage 5-20.6. If you are not installing memory modules in t

Installing AdaptersAdding an adapter, such as audio, communication, or specialized graphics, extendsthe capabilities and power of your system. Your s

1. If you have not already done so, remove the covers as described in “RemovingBoth the Front and Side Covers” on page 5-10.2. Remove the I/O planar c

4. Remove the expansion-slot cover:a. Loosen and remove the screw with a screwdriver.b. Slide the expansion-slot cover out of the system.c. Store the

5. Install the adapter:a. Carefully grasp the adapter and align the adapter with the expansion slotconnector.b. Press the adapter firmly into the expa

Removing Adapters1. If you have not already done so, remove the covers as described in “RemovingBoth the Front and Side Covers” on page 5-102. Remove

d. Carefully pull the adapter out of the system. Chapter 5. Installing Options 5-35

xviii IBM RS/6000 7025 F50 Series User's Guide

5. If you are not installing another adapter in this expansion slot, reinstall theexpansion-slot cover:a. Slide the cover over the open expansion slot

Upgrading or Adding a CPU CardYou may find media included with your new CPU card. Look at the label todetermine the minimum level of firmware required

6. If you are upgrading a CPU card, remove the installed CPU card:a. Remove the power cable from the CPU card by squeezing the tabs.b. The card is sec

b. Open the retainer hooks on the unused CPU card slot.c. Remove the connector cover from the unused CPU card slot.d. Place the new CPU card in the ca

10. Replace the covers as described in “Replacing Both the Front and Side Covers”on page 5-96.11. Restart the system and go to the system management s

Installing Internal DrivesIf you add different types of drives, your system can read multiple types of mediaand store more data. Several types of driv

ConsiderationsBay A comes with one 3.5-inch, 1.44MB diskette drive in A2 and a CD-ROM in A1.Bay B supports two 5.25-inch, or 3.5 inch half-high, remo

Preinstallation Steps (All Bays)Note: All internal drives in this system are mounted vertically.Attention: Caution should be used when handling all h

Installing a Disk Drive, Tape Drive, or CD-ROM in Bay A or Bay B1. If you have not already done so, remove the covers as described in “RemovingBoth th

SCSI Ultra Boot Disk4. You must also install the two gaskets that are shipped with the disk carrier if theywere not previously installed. Make sure t

Chapter 1. System StartupThank you for selecting an IBM RS/6000 7025 F50 Series system!The IBM RS/6000 7025 F50 Series system combines PowerPC 604 mi

5. Connect the 16-bit to 8-bit interposer that came with your SCSI device to thedrive.6. Check and place SCSI ID jumpers in correct position on the dr

7. Install the device:a. Position the device vertically, with the connectors facing the rear of thesystem.b. Align the device with the guides on the b

8. Slide the diskette drive and the CD-ROM drive forward in their guides to allowmore room for connecting cables to the new drive.a. Connect the cable

 Cable connections for connecting the integrated SCSI on the systemboard to backplane C.Attention Route the cables (SCSI-2 and power) at the rear of

9. If you installed a removable-media drive in bay B1 or bay B2, remove the coverplate from the front cover. A cover plate (complete bezel) is in plac

Installing a SCSI Disk Drive in Bank C, D, or E.Notes:  SCSI IDs are automatically assigned by the backplane for each bank.Therefore, no address jump

1. If you have not already done so, remove the front covers as described in“Removing the Front Covers Only” on page 5-62. Each drive you plan to insta

c. Align the side of the carrier with the raised guides on the bottom of the bay.d. Slide the carrier into the bay gently to keep from damaging the di

e. Move the carrier latch to the locked position. If the carrier will not lock, checkthat the drive carrier is fully seated in the backplane. When the

Installing a SSA Disk Drive in Bank C, D, or E.Notes:  Banks C, D, and E support hot-swappable disk drives only. SSA disk drive carriers and SCSI di

Second Edition (February 1998)The following paragraph does not apply to the United Kingdom or any country wheresuch provisions are inconsistent with l

Before You Begin Make sure you have an adequate number of properly grounded electrical outletsfor your system, display, and any other options you int

1. If you have not already done so, remove the front covers as described in“Removing the Front Covers Only” on page 5-62. If you are installing drives

c. Align the side of the carrier with the raised guides on the bottom of the bay.d. Slide the carrier into the bay gently to keep from damaging the di

e. Move the carrier latch to the locked position. If the carrier does not lock,check that the drive carrier is fully seated in the backplane. When the

Installing a SCSI Backplane in Bank D or ENotes:  Before installing SCSI disk drives in bank D or E, you must also orderand install:– A SCSI disk dri

5. Install the backplane at the rear of bank D or E:a. Align the top screw hole on the left side of the backplane with the top screwhole on the left s

6. Install an additional SCSI-2 adapter or RAID adapter (if necessary) in one of theempty PCI expansion slots. Refer to “Installing Adapters” on page

b. Attach the new power cable to backplane D or E.c. Connect the other end of the power cable to the power supply.d. After the connection have been ma

g. Connect the SCSI cable from the second SCSI internal connector to the newbackplane (D or E). Refer to the following illustrations to help you conne

8. Fill in the bank label. The bank label is located in the front of the system at theright side of the machine. Use the following table to help you d

9. If you have other drives to install, go to page 5-43.10. If you have other procedures to perform, refer to “Option List” on page 5-17.11. If you do

Unpacking Your SystemCAUTION:To avoid possible injury while moving or lifting the system, ask another personto help you.Moving the SystemWhen the syst

Installing a SSA Backplane in Bank D, or ENotes:  Banks C, D, and E support hot-swappable drives only. Before installing SSA disk drives in bank C,

1. Inventory your parts and tools. a. SSA backplane b. power cablec. SSA daisy chain cable (only needed if more than one SSA backplane isinstalled)d

6. Locate the new backplane.7. Attach the new power cable to backplane D.8. Locate the SSA bulkhead cable or internal SSA cable.5-68 IBM RS/6000 7025

9. Connect the SSA cable to the new backplane. Refer to the following illustrationsto help you connect the cables properly. Chapter 5. Installing

10. Connect the connector from the EPOW cable to backplane D as shown.5-70 IBM RS/6000 7025 F50 Series User's Guide

11. Install the backplane at the rear of bank D:a. Align the top screw hole on the left side of the backplane with the top screwhole on the left side

c. Connect the other end of the power cable to the power supply.5-72 IBM RS/6000 7025 F50 Series User's Guide

12. If you are using an internal SSA cable, connect the SSA cable to the SSAadapter. Refer to the PCI SSA 4-Port RAID Adapter Installation Guide forin

e. Attach the SSA cables from the SSA adapter to the SSA bulkheadconnectors, as show. Refer to the SSA documentation for information onconnecting thes

16. Remove the outside SSA cable from Backplane D, this cable is attached later inthese procedures. One end of the SSA daisy chain cable connects here

Preinstallation ChecklistAfter you unpack your system, display or ASCII terminal, and optional devices, makesure you have the following items:Ø Syste

18. Attach the new power cable to backplane E.19. Attach the SSA daisy chain cable to the connector on Backplane D.20. If the other end is not attache

Chapter 5. Installing Options 5-77

22. Install the backplane at the rear of bank E:a. Align the top screw hole on the left side of the backplane with the top screwhole on the left side

24. Connect the SSA cables that were removed from backplane D to the outsideSSA connector on backplane E. Chapter 5. Installing Options 5-79

25. SSA cables connected to SSA backplanes C, D, and E is shown below.26. If you have other procedures to perform, refer to “Option List” on page 5-17

Removing Internal DrivesWhere are you removing the drive? To remove a disk drive, tape drive, or CD-ROM from bay A or bay B, go to page5-82. To remo

Removing a Disk Drive, Tape Drive, or CD-ROM from Bay A or Bay BNote: To locate bay A or bay B, see the illustration given on page 5-81.To remove a d

Removing a SCSI Disk Drive from Bank C, D, or ENotes:  To locate banks C, D, and E, see the illustration given on page 5-81. You do not have to turn

To remove a hot swap drive from bank C, D, or E, do the following steps:1. If you have not already done so, remove the covers as described in “Removin

6. Disconnect the drive from the connector on the backplane, by grasping thehandle on the drive tray and carefully pulling the drive out of the system

Connecting the Cables1. If you are using a keyboard, attach the keyboard cable to the keyboardconnector ( ).2. If you are installing a mouse or othe

7. If you are removing another internal drive, return to step 2 on page 5-84.8. If you are installing another internal drive in bank C, D, or E, go to

Removing a SSA Disk Drive from Bank C, D, or ENotes:  To locate banks C, D, and E, see the illustration given on page 5-81. You do not have to turn

To remove a drive from bank C, D, or E, do the following steps:1. If you have not already done so, remove the covers as described in “Removingthe Fron

Attention: SSA backplanes must be fully populated. Each backplane connectormust have a disk drive or a blank carrier installed at all times. If you re

7. If you are removing another SSA disk drive, return to step 2 on page 5-88.8. If you are installing another SSA disk drive in bank C, D, or E, go to

Installing a U-BoltBefore you begin, be sure you have: A 19 mm (3/4 in.) U-bolt or wire rope (similar to National Manufacturing No.3230, STK No. 176-

2. Reinstall the system's side and front covers, and attach the cables (see“Replacing Both the Front and Side Covers” on page 5-96).3. Insert the

Replacing the Front Covers1. Reinstall the front cover:Note: Before installing the front cover, verify that the side cover is installedcorrectly. If

e. Lock the keylock on the front cover.f. Close the latch located on the left side of the front cover.5-94 IBM RS/6000 7025 F50 Series User's Gui

2. Reinstall the door at the front of the system by aligning the pins with the hinges,and sliding the door down.3. Close the door.Attention: Be sure t

Starting the System1. Open the door. If the diskette drive contains packing material or a diskette,remove it from the drive.2. Remove the extra key an

Replacing Both the Front and Side Covers1. Reinstall the side cover:a. Align the pins on the rear of the side cover with the two hinges on the rear of

2. Reinstall the front cover:Note: Before installing the front cover, verify that the side cover is installedcorrectly. If the side cover is not prop

e. Lock the keylock on the front cover.f. Close the latch located on the left side of the front cover.5-98 IBM RS/6000 7025 F50 Series User's Gui

3. Reinstall the door at the front of the system by aligning the pins with the hinges,and sliding the door down.4. Close the door.Attention: Be sure t

5. Connect all cables to the back of the system, then plug all power cords intoproperly grounded electrical outlets.Note: If you are in the United Ki

Replacing the I/O Planar Cover1. Place the lip at the top of the I/O planar cover over the top of the system adapterhousing. Push the bottom of the I/

5-102 IBM RS/6000 7025 F50 Series User's Guide

Chapter 6. Using the Online and Standalone DiagnosticsSources for the DiagnosticsThe diagnostics consist of Standalone Diagnostics and Online Diagnost

Undefined Terminal TypesIf an undefined terminal type from the DEFINE TERMINAL option menu is entered,the menu prompts the user to enter a valid termi

set up to boot from a server, the diagnostics are run in the same manner as theyare from disk. If the diagnostics are loaded from disk or a server, y

4. Press the Power On switch.5. Check your display or ASCII terminal for configuration information displayed asthe power-on self-test (POST) begins. T

General Attributes Always RequiredThe following general attributes are the default settings for the diagnostics. Be sureyour terminal is set to these

General SetupAttributes3151/11/31/41Settings3151/51/61Settings3161/3164SettingsDescriptionCRT saver Off Off 10 The "10" setting causes thedi

Additional Communication AttributesThe following communication attributes are for the 3151, 3161, and 3164 terminals.CommunicationSetupAttributes3151/

Additional Keyboard AttributesThe following keyboard attributes are for the keyboard attached to the 3151, 3161,and 3164 terminals.KeyboardSetupAttrib

Additional Printer AttributesThe following printer attributes are for a printer attached to the 3151, 3161, and 3164terminals.PrinterSetupAttributes31

Online Diagnostics Modes of OperationThe Online Diagnostics can be run in three modes:  Service Mode  Concurrent Mode  Maintenance Mode Service

Note: Pressing the F3 key (from a defined terminal) produces a "Confirm Exit"popup menu which offers two options: continuing with the shutd

The diag command loads the diagnostic controller and displays the OnlineDiagnostic menus.Running the Online Diagnostics in Concurrent ModeTo run Onlin

4. When a message indicates the system is in maintenance mode, enter the diagcommand.Note: It may be necessary to set TERM type again.5. When DIAGNOS

7. Follow the displayed instructions to checkout the desired resources.8. When testing is complete; use the F3 key to return to the DIAGNOSTICOPERATIN

Finishing the Installation Important  Be sure to maintain at least 51 mm (2 in.) of space on all sides of the systemto allow the system's cooli

Location CodesThis system unit uses Physical Location Codes in conjunction with AIX LocationCodes to provide mapping of the failing field replaceable

Specifically, the format of a location code is defined as follows:pn[.n][- or /]pn[.n][- or /]...Where p is a defined alpha location type prefix, n is

FRU NameAIXLocation CodePhysicalLocation CodePhysicalConnectionLogicalIdentificationMemory Card 2 00-00 P1-M2 ProcessorConnector J13 Memory Card 2DIM

FRU NameAIXLocation CodePhysicalLocation CodePhysicalConnectionLogicalIdentificationCard in PCI Slot1P20-58 to 20-5F P2-I1 I/O PlanarConnector J1Host

FRU NameAIXLocation CodePhysicalLocation CodePhysicalConnectionLogicalIdentificationSCSI BackplaneCWhenconnected toSCSI Port 1(P2/Z1)10-60-00-15, 0 P

FRU NameAIXLocation CodePhysicalLocation CodePhysicalConnectionLogicalIdentificationDASD in BaysD1 through D6Whenconnected toPCI adapter inslot P2-In

AIX Location CodesThe basic formats of the AIX location codes are: For non-SCSI devices/drives AB-CD-EF-GH For SCSI devices/drives AB-CD-EF-G,

 The EF value identifies a connector. The GH value identifies a port, address, device, or FRU.Adapters and cards are identified with just AB-CD.The

AB-CD-EF-G,H| | |||| | | | Logical Unit address of the SCSI Device| | | Control Unit Address of the SCSI Device| | Connector ID| devfunc Numbe

Integrated ISA adaptersNon-integrated ISA adaptersDevice attached to SCSI controller20-58 to 20-5F Any PCI card in slot 120-60 to 20-67 Any PCI card i

Chapter 2. Using the System UnitStarting the System Unit1. Set the power switches of the attached devices to On.Note: When the system is plugged in b

6-24 IBM RS/6000 7025 F50 Series User's Guide

Chapter 7. Using the Service AidsIntroduction to Service Aids ... 7-3Service Aids . . . . . . . . . . . . . . . . . . . .

SCSI Tape Utilities Service Aid ... 7-22Service Hints Service Aid ... 7-23Update System or Servic

Introduction to Service Aids Service AidsThe diagnostics contain programs called service aids. The service aids are used todisplay data and do additio

The following are descriptions of the service aids:AIX Shell Prompt Service AidThis service aid allows access to the AIX command line. In order to use

Call In allows the Service Processor to receive a call from a remote terminal. Call Out Authorized on S1 (on/off)Call Out Authorized on S2 (on/off)Ca

This is set to either 'first' or 'all'. If the call out policy is set to 'first', call out willstop at the first success

 Power On Via Ring Indicate (on/off) Number of Rings Before Power OnThis service aid may be accessed directly from the AIX command line, by entering

Note: A value of 0 indicates 'do not attempt to reboot' to a crashed system.This number is the maximum number of consecutive attempts to re

This service aid may be accessed directly from the AIX command line, by entering:/usr/lpp/diagnostics/bin/uspchrp -bSave or Restore Hardware Managemen

data. If you need information on the shutdown procedure for your operating system,see your operating system documentation.1. Before stopping the syste

Dials and LPFK Configuration Service AidThis service aid provides a tool for configuring and removing dials/LPFKs to thestandard serial ports.The Dial

patterns to the disk. An additional option allows data in a selectable block to beread and displayed on the system console.To use the Erase Disk optio

Disk Maintenance Service Aid Disk to Disk Copy Service Aid Display/Alter Sector Service AidDisk to Disk Copy Service AidThe service aid allows you t

Display/Alter Sector Service AidThis service aid allows the user to display and alter information on a disk sector.Care must be used when using this s

 Show Fix (APAR) Installation Status List Fileset Requisites List Fileset Dependents List Files Included in a Fileset List File Owner by FilesetD

The supported drawer types are: Media SCSI Device Drawer DASD SCSI DASD DrawerDisplay and Change Diagnostic Test List Service AidThis service aid pr

Display Previous Diagnostic Results Service AidNote: This service aid is not available when you load the diagnostics from a sourceother than a disk d

Generic Microcode Download Service AidThis service aid provides a means of restoring a diskette (or other media) andexecuting a restored program. This

This service aid is only supported by the Standalone Diagnostics. SMIT should beused to configure ISA adapters for AIX.ISA adapters cannot be detected

Optical Disk Service Aids The Optical Disk Service Aids consist of Initialize, Format and Certify, and SpareSector Availability service aids.  Initi

Reading the Operator Panel DisplayThe operator panel display is used to: Track the progress of the system unit self tests and configuration program.

SCSI Bus Analyzer TaskThis service aid provides a means to diagnose a SCSI Bus problem in a free-lancemode.To use this service aid, the user should ha

The SCSI Bus Service Aid transmits a SCSI Inquiry command to a selectable SCSIAddress. The service aid then waits for a response. If no response is re

SCSI Tape Utilities Service AidThis service aid provides a means to obtain the status or maintenance informationfrom a SCSI tape drive. Only some mode

 Display or copy a tape drive's log sense information.The service aid will provides options to display the log sense information toscreen, to co

the file /var/update_flash_image can be removed to conserve space in the /var filesystem.Display Firmware Device NodeNote: Runs on CHRP systems units

7135 RAIDant Array Service AidThe 7135 RAIDant Array service aids contain the following functions:  Certify LUNThis selection reads and checks each

7-26 IBM RS/6000 7025 F50 Series User's Guide

Chapter 8. Using the System Verification ProcedureThe system verification procedure is used to check the system for correct operation.When you are ana

Step 2. Loading the Diagnostics1. Stop all application programs running on the operating system.2. Stop the operating system.3. Turn the power off.4.

Step 3. Running System VerificationThe Diagnostic Operating Instructions should be displayed.1. Press the Enter key.2. If the terminal type has not be

ContentsCommunications Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . viiFederal Communications Commission (FCC) Statement ...

Using the KeyboardsThere are several keyboards available for the system unit. The keyboards havevarious keys that enter data and control the cursor lo

Step 5. Stopping the Diagnostics1. If running Online diagnostics, the system first should be shut down using thefollowing procedure:a. Press F3 repeat

Chapter 9. Hardware Problem DeterminationProblem Determination Using the Standalone or Online DiagnosticsUse this procedure to obtain a service reques

Step 3Determine if the operating system is accepting commands.Is the operating system accepting commands?NO The system must be turned off in order

Step 5This step invokes the Online Diagnostics in concurrent mode.1. Log on as root or as superuser.2. Enter the diag command.3. Wait until the Di

Step 7Starting at the top of the following table, find your symptom and follow theinstructions given in the Action column. Step 8The following

Step 10There is a problem with the keyboard.Find the type of keyboard you are using in the following table, then follow theinstructions given in t

Step 111. If the terminal type has not been defined, you must use the InitializeTerminal option on the Function Selection menu to initialize the o

Step 12Did the Diagnostic Selection Menu display?NO If Problem Determination was selected from the Diagnostic ModeSelection menu, and if a recent

Step 14The diagnostics produced an SRN for this problem.1. Record the SRN and other numbers read out.2. Report the SRN to the service organization

Step 16This step loads the Standalone Diagnostics. If you are unable to load thediagnostics, go to “Step 7.”1. Turn the power on.2. Insert the dia

On all of the keyboards, you can adjust the tilt position for typing comfort. To tilt thekeyboard, pull out on the keyboard legs. The legs snap into p

Problem Determination When Unable to Load DiagnosticsUse this procedure to obtain an error code. The service organization uses the errorcode to determ

Step 3This step attempts to load Online Diagnostics in service mode.1. Turn the power to off.2. Turn the power on.3. If the keyboard indicator app

Step 5Starting at the top of the following table, find your symptom and follow theinstructions given in the Action column.Symptom ActionThe power

Symptom ActionThe system does not respond when thepassword is entered.Go to Step 7. The system stopped and an indicator isdisplayed on the system cons

Step 6The diagnostics loaded correctly.Go to “Problem Determination Using the Standalone or Online Diagnostics” onpage 9-1. Step 7There is a p

Appendix A. System RecordsRecord the Identification NumbersRecord and retain the following information.The server's identification numbers are l

Device RecordsUse the following tables to keep a record of the options installed in or attached toyour system. This information can be helpful when y

Refer to the following diagram of your server's bays when completing Table A-2 onpage A-4.Notes:  If you attach a drive or other device to an a

Table A-2. Internal Files and DevicesAdapter Location SCSI ID Drive Description Integrated Bay A1 4 CD-ROM Drive Integrated Bay A2 Non-SCSI 3.5-Inch

Appendix B. Replacing the BatteryThe manufacturer has designed this product with your safety in mind. The lithiumbattery must be handled correctly to

Using the Three–Button MouseThe mouse is a hand–operated locating device. A three–button mouse is availablefor use with the system unit.Consult your a

Note: After you replace the battery, you must reconfigure your system (custom bootlist, IP parameters, etc.) and reset the system date and time.1. If

4. Remove the battery:a. Use one finger to slightly slide the battery toward the front of the server.(The spring mechanism behind the battery pushes i

B-4 IBM RS/6000 7025 F50 Series User's Guide

Appendix C. Service Processor Setup and TestFor your convenience, here is an example Service Processor setup checklist. It isbasic. Your setup may inc

Testing the SetupThe following is a sample procedure to assure your setup is working.These tests include communicating with the server operating syste

2. Call your server again.3. At the Service Processor Main Menu, select Call-In/Call-Out Setup menu, thenselect Call-Out test. This causes a simulated

C-4 IBM RS/6000 7025 F50 Series User's Guide

Appendix D. Modem ConfigurationsSample Modem Configuration FilesWith nearly 1000 modems to choose from, and various programming standards,configuring

Configuration File Selection1. Does your modem respond to the extended command set (prefixed with &)?If yes, go to 3 If not, continue with 2 below

4. Does your modem respond to:a. AT&F reset command, orb. AT&Fn reset commands, where n can be 0, 1, etc.?If AT&F, configuration file mode

With the mouse buttons, you can perform functions such as selecting anddeselecting options, extending your selection, or choosing a command. The preci

Note: If you have already set up your serial ports, line speeds, authorizations andtelephone numbers from the Service Processor menus, specify your c

Ring DetectionMost modems produce an interrupt request each time they detect a ring signal.Some modems generate an interrupt only on the first ring s

If your modem communicates properly with remote users, it is probably in control. Itmay be wise to occasionally change some of the functional settings

With the remote terminal connected to serial port 1 and defined as the primaryconsole device, there are two tests you can perform:1. Will the modem dr

Prevention StrategyThe disconnect is caused by the operating system when it initializes the primaryconsole. The tests listed above are conducted with

Modem Configuration SamplesSample File modem_z.cfg # # COMPONENT_NAME: (ESPSETUP) ENTRY SERVICE PROCESSOR SETUP Z # # FUNCTIONS: Modem configuration f

retry: send "A/" # Repeat the previous command.# Expect a connection response.expect "16\r" or "15\r" or "14\r&quo

Sample File modem_z0.cfg # # COMPONENT_NAME: (ESPSETUP) ENTRY SERVICE PROCESSOR SETUP Z # # FUNCTIONS: Modem configuration file for some early Hayes

expect "16\r" or "15\r" or "14\r" or "12\r" or "1\r" or "5\r" or "1\r" busy &qu

Sample File modem_f.cfg # # COMPONENT_NAME: (ESPSETUP) ENTRY SERVICE PROCESSOR SETUP F # # FUNCTIONS: Modem configuration file for many recent Hayes

Care of the MouseThe operating surface for the mouse should be smooth, clean, and flat. Forexample, you can operate the mouse on the following surface

done retry: send "A/" # Repeat the previous command.# Expect a connection response.expect "16\r" or "15\r" or "14

expect "8\r" or "7\r" or "6\r" or "4\r" or "3\r" delay 2 done Appendix D. Modem Configurations

Sample File modem_f0.cfg # # COMPONENT_NAME: (ESPSETUP) ENTRY SERVICE PROCESSOR SETUP F # # FUNCTIONS: Modem configuration file for many recent Hayes

expect "16\r" or "15\r" or "14\r" or "12\r" or "1\r" or "5\r" or "1\r" busy &qu

done # RI Power On enabled. error: # Handle unexpected modem # responses.expect "8\r" or "7\r" or "6\r" or "4\r&qu

Sample File modem_f1.cfg # # COMPONENT_NAME: (ESPSETUP) ENTRY SERVICE PROCESSOR SETUP F1 # # FUNCTIONS: Modem configuration file for many recent Hayes

timeout 6 done retry: send "A/" # Repeat the previous command.# Expect a connection response.expect "16\r" or "15\r"

error: # Handle unexpected modem # responses.expect "8\r" or "7\r" or "6\r" or "4\r" or "3\r" del

D-22 IBM RS/6000 7025 F50 Series User's Guide

Appendix E. Service Processor Operational PhasesThis section provides a high-level flow of the phases of the Service Processor (SP).SP Power Applied │

Cleaning the Mouse1. Remove the retaining ring by turning it counterclockwise, in the direction of thearrow as shown in the illustration.2. Remove the

Standby PhaseThe standby phase can be reached in two ways:1. With the server OFF and power connected (the normal path), recognized by OK inthe LCD di

The SP can dial a pre-programmed telephone number in the event of an IPLfailure. The SP issues an error report with the last reported IPL status indic

E-4 IBM RS/6000 7025 F50 Series User's Guide

IndexNumerics3.5–inch diskette driveusing 2-104-mm tape cartridgeloading 2-39unloading 2-404.0GB 4-mm tape drivegeneral information 2-31status lig

Ddevice records A-2internal and external options A-2internal files and devices A-4devices, startup 3-8diagnostic considerationsrunning from a TTY term

installing a disk drive in bank C, D, orE. 5-51installing a SSA backplane in bank D,or E 5-66installing a SSA disk drivein bank C, D, or E 5-55instal

modem_f1.cfg, sample file D-19modem_z.cfg, sample file D-9modem_z0.cfg, sample file D-11 modes of operationonline diagnostics 6-9mouseusing 2-6Nnonre

removing adapters 5-34removing both the front and sidecovers 5-10removing internal drives 5-81removing memory 5-28removing the front covers only 5-6

static-sensitive devices, handling 5-3STBY E-2stopping the system unit 2-1storage devices 5-4surveillancefailure 4-29operating system 4-29set parame

Index X-7

Using the 3.5–Inch Diskette Drive Diskette CompatibilityThe system unit has a 1.44MB diskette drive installed vertically in the front.The 1.44MB diske

X-8 IBM RS/6000 7025 F50 Series User's Guide

Reader's Comments — We'd Like to Hear From You&title.Part Number: &partnum.Overall how satisfied are you with the information in thi

X-10 IBM RS/6000 7025 F50 Series User's Guide

IBMPart Number: 07L8342Printed in the United States of Americaon recycled paper containing 10%recovered post-consumer fiber.February 1998SA38-54-1

 To allow writing onto a diskette, slide the write–protect tab to cover the protectslot.Loading and Unloading the 3.5–Inch DisketteTo load a diskette

Using the CD–ROM DriveCAUTION:A Class 3 laser is contained in the device. Do not attempt to operate the devicewhile it is disassembled. Do not attempt

Loading the CD–ROM DrivePress the unload button to open the tray. Place the disc, with the printed side awayfrom the tray, into the tray. Slip out the

Using the 4.0GB 4-mm Tape Drive ... 2-37Chapter 3. System Management Services ... 3-1Graphical System Manageme

Emergency EjectNote: Execute the following procedure only in an emergency (tray will not ejectalthough pressing the unload button).1. Insert a small

Using the Hot Swap Disk DrivesFor information on installing hot swap drives refer to “Installing a SCSI Disk Drive inBank C, D, or E.” on page 5-51.Fo

2-16 IBM RS/6000 7025 F50 Series User's Guide

Handling GuidelinesThe hot-swap disk drive is a sensitive device. Handle the hot-swap carrier and diskdrive with care. Do not drop the disk drive or

Disk Drive Status LED StatesSCSI Disk Drives: The following table explains the meaning of the green andamber status LEDs and spin down button.Status

SSA Disk Drives: The following table explains the meaning of the Power, Readyand Check status LEDs.Status LEDsLED Status DefinitionPower On Power OnO

General Information for 8-mm Tape Drive Recommendations Use only Data Grade 8-mm tape cartridges. These cartridges are identified byeither a Data, D,

Tape Cartridge CompatibilityThe 8-mm tape drive is compatible with existing 8-mm tape subsystems that complyto the American National Standard (ANSI) X

Environment Considerations for 8-mm Data CartridgesInformation in this section describes operating and storage conditions includingtemperature, relati

Operating in Harsh EnvironmentsThe 8-mm tape drive is ideally suited to streaming operations, as opposed to tapemovement operations involving multiple

Removing a SSA Disk Drive from Bank C, D, or E ... 5-87Installing a U-Bolt ... 5-91Replacing the Front C

Using the 5.0GB 8-mm Tape DriveThe optional 5.0GB 8-mm tape drive is a half-height device. Status LightsThe 5.0GB 8-mm tape drive has two green status

Status Light StatesThe following table explains the meaning of the green and amber status lights.Status Lights on the 5.0GB 8-mm Tape DriveStatus Read

Loading the 8-mm Tape CartridgeBefore loading the tape cartridge, make sure the power is on and the write-protecttab on the tape cartridge is properly

Commands can be entered while the tape is loading. Any commands to the tapedrive start running once the tape has finished loading. Commands not requir

Unloading the 8-mm Tape CartridgeBefore performing the unload operation, make sure the power to the 8-mm tape driveis on.To unload and eject the tape

The time required for a tape to rewind and unload is between 18 seconds and 3minutes, depending on the position of the tape when the unload button is

After the 8-mm cleaning cartridge has been fully inserted into the 8-mm tape drive,the following cleaning operations are performed automatically:1. Th

General Information for 4.0GB 4-mm Tape DriveThe 4.0GB 4-mm tape drive is a streaming tape drive that is used to: Save and restore system data files.

RecommendationsAttention: Tape cartridges that do not carry the proper DDS symbol cannot bewritten to and their use may cause the 4-mm tape drive to

Tape Cartridge CompatibilityThe 4-mm Tape Drive is compatible with existing 4mm tape subsystems that aredesigned to operate with Digital Data Storage

SCSI Tape Utilities Service Aid ... 7-22Service Hints Service Aid ... 7-23Update System or Servic

Setting the Write-Protect Tab on 4-mm Tape CartridgesThe window on the tape cartridge controls write-protection. When the write-protecttab of a tape c

Environmental Considerations for 4-mm Data CartridgesInformation in this section describes operating and storage conditions includingtemperature, rela

Operating in Harsh EnvironmentsThe 4-mm tape drive is ideally suited to streaming operations, as opposed to tapemovement operations involving multiple

Using the 4.0GB 4-mm Tape DriveThe optional 4.0GB 4-mm tape drive is a half-high device. Status LightsThe 4.0GB 4-mm tape drive has two green status l

Status Light StatesThe following tables explain the meaning of the green and amber status lights. Ready (green) Read-Write (green) Disturbance (amber

Loading the 4-mm Tape CartridgeBefore loading the tape cartridge, make sure the power is on and the write-protectswitch on the tape cartridge is prope

Unloading the 4-mm Tape CartridgeBefore performing the unload operation, make sure the power to the 4-mm tape driveis on.To unload and eject the tape

Cleaning the Tape Path on the 4.0GB 4-mm Tape DriveThe 4-mm tape path should be cleaned either approximately every 30 hours of tapemotion or once a mo

2. The drive is cleaned by moving the cleaning tape forward for approximately 30seconds.3. The tape is unloaded and the cleaning cartridge is ejected

Chapter 3. System Management ServicesThe System Management Services make it possible for you to view informationabout your computer and to perform suc

Communications StatementsFederal Communications Commission (FCC) StatementNote: This equipment has been tested and found to comply with the limits f

To enter the graphical System Management Services instead of the Open Firmwarecommand line, you must press the F1 key after the keyboard icon appears

The System Management Services screen contains the following choices.Config: Enables you to view your system configuration.MultiBoot: Invokes the Muli

To select an icon, move the cursor with the arrow keys to choose which icon ishighlighted, then press the Enter key. You can also select an icon by cl

ConfigSelecting this icon makes it possible for you to view information about the setup ofyour system unit. A list similar to the following appears w

Selecting the down arrow key or Page Down key displays the next configurationscreen, which lists your computer's firmware version, the date of it

MultiBoot:This selection invokes the Mulitboot menu which provides several functions: To Select a particular operating system to boot.In the case of

this would mean that information in non-volatile storage could have been lost, aswould happen if the battery had been removed. In order to recreate th

Attention: If you change your startup sequence, you must be extremely carefulwhen performing write operations (for example, copying, saving, or format

UtilitiesSelecting this icon enables you to perform various tasks and view additionalinformation about your computer.The following describes the choi

Update: Allows you to update the firmware programs on yourcomputer.Console: If you have more than one display attached to yoursystem unit, or if you h

other optional cards, not supplied by the manufacturer, do not use main voltages orany other excessive voltages. Seek advice from a competent engineer

PasswordWhen you select this icon, the following screen is displayed.Power-On Password: Setting a power-on password helps protect information storedi

Press Enter when you are finished; you are required to type the password again forverification.If you make a mistake, press the Esc key and start agai

Remote Mode: The remote mode, when enabled, allows the system to start fromthe defined boot device. This mode is ideal for network servers and other

After you have entered and verified the password, the privileged-access passwordicon flashes and changes to the locked position to indicate that your

Error LogSelecting this icon displays the log of errors your computer has encountered duringoperations.Selecting the Clear icon erases the entries in

RIPLSelecting the Remote Initial Program Load (RIPL) icon above gives you access tothe following selections. Chapter 3. System Management Services

The Set Address icon allows you to define addresses from which your computer canreceive RIPL code.Notes:1. Some applications may require that IP addre

The Ping icon allows you to confirm that a specified address is valid by sending atest transmission to that address.After choosing the Ping option, yo

The Config icon allows you to configure network adapters which require setup.Selecting the Config icon presents a list of the adapters requiring confi

SCSI IDThis selection allows you to view and change the addresses (IDs) of the SCSIcontrollers attached to your system unit. To change an ID, highlig

This is a Class B product based on the standard of the Voluntary Control Council forInterference from Information Technology Equipment (VCCI). If this

UpdateThis selection allows you to update the service processor and system firmware inyour system unit from an image on a 3.5 inch diskette. After ch

Firmware RecoveryIf a troubleshooting procedure has indicated that the firmware information in yoursystem unit has been corrupted, then you must perf

Text-Based System Management ServicesThe text-based Open Firmware command line and System Management Services areavailable if an ASCII terminal is att

After the text-based System Management Services starts, the following screenappears.à ðSystem Management Services 1. Display Configuration 2. Multiboo

Display Configuration This option provides information about the setup of your computer. A screen similarto the following is displayed.à ð Device

MultiBoot Menuà ðMultiboot Menu 1. Select Software 2. Software Default 3. Install From 4. Select Boot Devices 5. OK Prompt 6. Mulitboot Startup <O

The OK Prompt procvides access to the Open Firmware command prompt. TheOpen Firmware command prompt is used for debug purposes, and device driverdevel

à ðCurrent Boot Sequence 1. Diskette 2. Ethernet (Integrated) 3. SCSI CD-ROM id=3 (slot=1) 4. SCSI 5MB Hard Disk id=6 (slot=1) 5. SCSI 5MB Hard Di

Selecting any of the Configure Boot Device options displays the following screen.à ðConfigure Nth Boot Device Device Number Current Position Device N

UtilitiesThe Utilities screen enables you to select from the following system managementtools.à ðUtilities 1. Set Password and Unattended Start Mode