IBM T200F User Manual Page 37
- Page / 126
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
TapeAlert Log
The TapeAlert log page is page 2Eh. There are 64 parameters, numbered from 1
through 64. Only parameters 1 through 18, 20 through 23, and 29 through 39 have
definitions for tape drives without attached loaders. The remaining parameters are
always 0.
All parameters are 1 byte long. Each parameter is either 0 to indicate the
corresponding condition has not occurred or 1 to indicate that the corresponding
condition has occurred. All log parameters are cleared when the log is read. The
Log is also cleared at power-on, on a reset condition, or by a LOG SELECT
command. Specific flags may be cleared when corrective action has removed the
condition that caused the flag to be set.
The supported parameters are listed in Table 22. For a description of service
actions associated with these parameters, refer to the IBM Ultrium Internal Tape
Drive Models T200 and T200F Setup, Operator, and Service Guide or the IBM 3580
Ultrium Tape Drive Setup, Operator, and Service Guide.
Table 22. TapeAlert Log Parameters
Parameter Description Type DU LP LBIN
3 Hard Error Warning 1 0 0
4 Media Critical 1 0 0
5 Read Failure Critical 1 0 0
6 Write Failure Critical 1 0 0
7 Media Life Warning 1 0 0
8 Not Data Grade Warning 1 0 0
9 Write Protect Critical 1 0 0
10 No Removal Information 1 0 0
11 Cleaning Media Information 1 0 0
12 Unsupported Format Information 1 0 0
15 Memory in Cartridge Failure Warning 1 0 0
16 Forced Eject Critical 1 0 0
18 Tape Directory Corrupted Warning 1 0 0
19 Nearing Media Life Information 1 0 0
20 Clean Now Critical 1 0 0
21 Clean Periodic Warning 1 0 0
22 Expired Cleaning Media Critical 1 0 0
23 Invalid Cleaning Cartridge Critical 1 0 0
30 Hardware A Critical 1 0 0
31 Hardware B Critical 1 0 0
32 Interface Warning 1 0 0
33 Eject Media Critical 1 0 0
34 Download Fault Warning 1 0 0
35 Drive Humidity Warning 1 0 0
36 Drive Temperature Warning 1 0 0
37 Drive Voltage Warning 1 0 0
Chapter 2. Command Support 23
|
|
|
|
- SCSI Refer ence 1
- Contents 5
- Contents v 7
- Tables ix 11
- Organization 13
- Related Publications 13
- Chapter 1. Introduction 15
- SCSI Attachment 17
- Fibre Channel Attachment 17
- Supported Device Drivers 18
- Chapter 2. Command Support 19
- Chapter 2. Command Support 7 21
- Chapter 2. Command Support 9 23
- Unit Serial Number Page 24
- Device Identification Page 25
- Chapter 2. Command Support 13 27
- LOAD/UNLOAD 28
- Chapter 2. Command Support 15 29
- LOG SELECT 30
- LOG SENSE 31
- Log Page Format 32
- Supported Log Pages 33
- Write Error Counters Log 34
- Read Error Counters Log 35
- Sequential Access Device Log 36
- TapeAlert Log 37
- Tape Usage Log 38
- Tape Capacity Log 38
- Data Compression Log 39
- MODE SELECT 40
- MODE SENSE 41
- Mode Data Format 42
- Mode Parameter Header 42
- Mode Block Descriptor 43
- Disconnect/Reconnect Page 44
- Data Compression Mode Page 45
- Chapter 2. Command Support 33 47
- Chapter 2. Command Support 35 49
- PERSISTENT RESERVE IN 50
- Chapter 2. Command Support 37 51
- PERSISTENT RESERVE OUT 53
- PREVENT/ALLOW MEDIUM REMOVAL 55
- READ ATTRIBUTE 57
- Chapter 2. Command Support 45 59
- Attribute 60
- Chapter 2. Command Support 47 61
- READ BLOCK LIMITS 62
- READ BUFFER 63
- Boundary 64
- Error Log Buffer 65
- READ POSITION 66
- RECEIVE DIAGNOSTIC RESULTS 67
- RELEASE UNIT 68
- REPORT DENSITY SUPPORT 69
- Chapter 2. Command Support 57 71
- REPORT LUNs 72
- REQUEST SENSE 73
- Sense Data Format 74
- Chapter 2. Command Support 61 75
- RESERVE UNIT 77
- SEND DIAGNOSTIC 79
- Self-Test 79
- SIM Data Structure 80
- Chapter 2. Command Support 67 81
- MIM Data Structure 82
- Chapter 2. Command Support 69 83
- Force Dump 85
- Write Dump To Cartridge 86
- Post A Self Test Diagnostic 87
- Post B Tape Test Diagnostic 88
- Post C Media Test Diagnostic 89
- Post D Head Test Diagnostic 90
- Set Traps 91
- Remove Traps 92
- Chapter 2. Command Support 79 93
- Reset Drive 94
- Chapter 2. Command Support 81 95
- TEST UNIT READY 96
- Chapter 2. Command Support 83 97
- WRITE ATTRIBUTE 98
- WRITE BUFFER 99
- WRITE FILE MARKS 100
- Sense Data 101
- Sense Data Management 101
- Unit Attention Conditions 101
- Persistent Errors 102
- Common Tape LUN Behaviors 107
- Power-On 107
- Reset Strategy 107
- Abort Handling 108
- Multi-initiator Support 110
- Status Codes 110
- LUN Identification 111
- Bus Parity Errors 111
- Disconnect Strategy 111
- Messages 112
- Message In 113
- Extended Messages 114
- Appendix. Notices 117
- How to Send Your Comments 118
- Trademarks 119
- BUSINESS REPLY MAIL 124
Related products and manuals for Tape drives IBM T200F
Tape drives IBM 40/80 GB DLT User Manual
(56 pages)
(56 pages)
Tape drives IBM 3580S6E Datasheet
(4 pages)
(4 pages)
Tape drives IBM 49Y9898 Datasheet
(13 pages)
(13 pages)
Tape drives IBM 3628L3X Datasheet
(13 pages)
(13 pages)
Tape drives IBM 46C5388 Datasheet
(15 pages)
(15 pages)
Tape drives IBM 3628L4X Datasheet
(13 pages)
(13 pages)
Tape drives IBM 3573E44 Datasheet
(4 pages)
(4 pages)
Tape drives IBM 3572S4R Datasheet
(24 pages)
(24 pages)
Tape drives IBM 46C5399 Datasheet
(13 pages)
(13 pages)
Tape drives IBM 3572S5R Datasheet
(4 pages)
(4 pages)
© 2020, manymanuals.com. All rights reserved. | 0.752 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals